Mantra Filtration provide Electrostatic Precipitator Systems to its clients. The process of Electrostatic precipitation helps in removing particles from exhaust gas stream of an industrial process. As often the procedure involve combustion, this safeguard against emission of particles to the atmosphere.

Here six activities typically take place:
Ionization - Charging of particles
Collection - Precipitation of the charged particles onto the collecting surfaces
Migration - Transporting the charged particles to the collecting surfaces
Particle Removal - Conveying the particles from the hopper to a disposal point
Charge Dissipation - Neutralizing the charged particles on the collecting surfaces
Particle Dislodging - Removing the particles from the collecting surface to the hopper

We offer Electrostatic Precipitator Systems with below features:

Low Pressure Drop
Low Maintenance
High Collecting efficiency well in excess of 99%
Low sensitivity to high temperature and aggressive gases


Discharge Electrode and Emitting Springs offered by us is the heart of any Electrostatic precipitator with characteristics including superior ESP performance. Its annealed copper nails also ensure sharp corona points over a long time. Most advantages of D.E. is:

   • Higher corona generation
   • Lower corona onset voltage

We can fulfill customer’s discharge electrode needs for most designed Electrostatic Precipitators. Here, we can supply them with material, style & size to fit requirements of their existing precipitation system in straight round wire, barbed discharge wire, rigid frames, rigid masts, rigid spiked pipes, & spiral wires. We also hold expertise in supplying of discharge electrodes that are suitable for all types of ESP like:

  • Thermax
  • Alstom
  • ACC
  • VT Corp
  • ELS-Elex


The High voltage support insulators offered by us mechanically support as well as electrically isolate discharge electrodes from grounded ESP casing & collecting curtains. Support insulators are designed for delivering high compressive strength to support loads imposed by high voltage electrodes as well as associated framing. Providing primary application point for high voltage & located in close proximity to gas stream, these high voltage support insulator’s design must also consider voltage applied and operating environment.

We can offer support insulator that are suitable for all types of ESP like:
   • Thermax
   • Alstom
   • ACC
   • vt corp
   • els-elex

We can also supply various insulators for any type of ESP as follows:
   • Shaft insulators
   • Pin insulators
   • Bust duct insulators
   • Wall through bushing insulators
   • Antis way insulator


We offer customers a wide range of collecting plates that find application in electrostatic precipitators. These plates are made from rolled steel and are precision welded together in factory so as to reduce installation time at the jobsite. Further, each plate contains electrodes that are positively charged and when the particulate gas enters electrostatic precipitator and is struck with negative charge electrode, positively charged plates act as magnet and pull particulate gas to them. Some other features of these collecting plates include:

• Plates have both top & bottom stiffeners and plates that allow better mounting and ability to deal with   more abuse from rappers (Plates are arranged to form a series of gas passages)
• There can be anywhere from 30-35 passages inside electrostatic precipitator shell (Plates are    placed parallel to incoming particulate gas)
• We can supply collecting plates suitable for all types of ESP like thermax, alstom, acc, vt corp,
   els-elex etc.


MIGI rapper coil offered by us is a general use rapper ideal for most applications. It is capable of delivering strong shearing forces so as to remove even most tenacious of dusts from collecting curtains as well as rigid mast designed high voltage systems. We can also deliver these in specifications as demanded by the customers.




Discharge Electrode and Emitting Springs offered by us is the heart of any Electrostatic precipitator with characteristics including superior ESP performance. Its annealed copper nails also ensure sharp corona points over a long time. Most advantages of D.E. is:

Higher corona generation
Lower corona onset voltage

We can fulfill customer’s discharge electrode needs for most designed Electrostatic Precipitators. Here, we can supply them with material, style & size to fit requirements of their existing precipitation system in straight round wire, barbed discharge wire, rigid frames, rigid masts, rigid spiked pipes, & spiral wires. We also hold expertise in supplying of discharge electrodes that are suitable for all types of ESP like:
   • Thermax
   • Alstom
   • ACC
   • VT Corp
   • ELS-Elex
High Collecting Efficiency
Low Maintenance & Operative Costs